Product Range for Low Pressure Die Casting Industry
Release Agent and Protective Coating
» Excellent adhesion » Excellent release agent, especially in applications with non ferrous melts » Reduction of erosion by the melt and therefore » Reduced carryover of ferrous contaminants into the melt » Improvement of ingot surface quality » Outstanding non-wetability against molten metals » High thermal conductivity » Resists build up of dross
Cast-M Release Agent And Protective Coating For The Aluminum Industry
» Water-based coating » Environmentally friendly » No toxic fumes decomposition products when heated » Dries easily thanks to the low water content » The pasty consistency prevents separation and sedimentation of the solid particles during storage. » Free choice of application technology (e.g. brushing, spraying, dipping) » No preheating of the casting ladle required » Coating thicknesses up to 1.5 mm are possible » Binder permits long lifetime and increases productivity » No cracking of the coating due to frequent temperature cycles
Cast-G Metallurgical Protective Coating And Release Agent
» This binder permits unparalleled adhesion to the substrate. The type of graphite is immaterial. No particular pretreatment of the substrate is necessary. » The binder permits coating thick nesses up to 1 mm without the risk of ﬂ aking off. That makes it easy to make local repairs to damaged coatings. » The coatings can be applied thickly to repair holes and cracks. » Thixotropy permits the solid particles separating out and sedimenting during storage.
Cast-C Release Agent And Protective Coating For The Aluminum Industry
» This binder permits an unparalleled adhesion to all kinds of substrates. It is immaterial whether the substrate is a non-porous cement or a highly porous ﬁ ber material. No particular pretreatment of the substrate is necessary » The binder permits coating thicknesses upto 1 mm without the risk of ﬂaking off. That makes it easy to make local repairs to damaged coatings. » The coatings can be applied thickly to repair holes and cracks in the refractory lining. This eliminates the laborious removal of existing boron nitride coatings that would otherwise be needed with refractory materials » The number of castings per coating can be increased. » Thixotropy permits the solid particles separating out and sedimenting during storage.
Boron Nitride Release Agents For Aluminum Extrusion
» Outstanding release properties and lubrication » Improved safety and cleanliness in the press area: no open gas flames » Economical powder consumption » Reduced coating frequency: shorter downtimes » Increased productivity » Optimized product quality » Not harmful to health
» High resistance to molten metals and glass » Outstanding thermal shock resistance » Excellent electrical insulation - even at high temperatures » Application temperature 800 °C in air and 2000 °C in inert atmosphere
» Long life typically > 12 months » Excellent temperature response - melt temperature can be determined after approx. 1 min. » Unaffected by corrosion throughout its lifetime » No melt contamination » Can be used in melts containing sodium and strontium » High temperature resistance (up to approx. 1100 °C) » High thermal shock resistance » No preheating required » Resists build up of dross » Reduced maintenance requirements and ease of maintenance » Electrically insulating » Affordable
» Zero open porosity to maintain the pressure differential » Long life > 12 months » Unaffected by corrosion » No melt contamination » Can be used in melts containing sodium and strontium » Resists build up of dross » High temperature resistance (1100 °C) » High thermal shock resistance » No preheating required » Easy and reduced maintenance » Cost effective
» Gas-tight » Long life > 12 months » Unaffected by corrosion » No melt contamination » Can be used in melts containing sodium and strontium » Resists build up of dross » High temperature resistance up to 1,300°c » High thermal shock resistance » No preheating required at operation temperature below 900°c » Easy cleaning of bake-on » High thermal conductivity » Suitable for gas burners » Suitable for electrical heating systems » Best price performance ratio
» Electrical and gas fired immersion heating is the state of the art technology for the melting and holding of aluminium. » Variety of immersion heater tubes in different sizes and for various fixing devices. New solutions are done on customer request. » Diameters up to 300mm and length up to 1200mm can be realized.